★ 4.9 (600+ Google Reviews) · Marine Veteran-Owned · AZ ROC #333915

Garage Door Opener Repair & Installation in Phoenix.

We repair LiftMaster, Chamberlain, Craftsman, Genie and most other openers, and install new LiftMaster and Genie openers for $800–$1,400 installed, labor included.

  • LiftMaster (our go-to) and Genie installed
  • Chamberlain and Craftsman repaired
  • Remotes, keypads and HomeLink programmed
  • $100 off a new opener install

$49.95 visit waived with any repair · Phones answered 24/7 · Techs Mon–Sat 8–6

LiftMaster belt-drive opener with the Garage Door Grunts service sticker
A new LiftMaster 6580L belt drive Jack installed in Glendale (85307), October 2026.

What’s your garage door opener doing?

Most opener calls come down to a handful of causes. Pick what you’re seeing for the likely cause and what we’d do. Every repair is priced in writing before we start, and the $49.95 visit is waived when you approve the repair.

Opener hums, door doesn’t move

A stripped gear and sprocket, a worn trolley, or the red release cord was pulled.

What we do: We check the springs first, then rebuild or replace the drive, priced in writing.

Door reverses or won’t close

Dirty or misaligned safety sensors, low afternoon sun, or a limit/force setting that drifted.

What we do: Clean and realign the eyes, repair sensor wiring, reset limits and force, test the safety reverse.

Remote or keypad stopped working

Dead batteries, a lost code or an old remote that doesn’t match the opener.

What we do: Program remotes, keypads and HomeLink on the visit; LiftMaster remotes cover most Chamberlain and Craftsman openers.

Grinding, straining, loud

Worn gears, or tired springs making the opener lift the door.

What we do: Fix the cause, not just the noise: gears, springs, rollers and a lube on every visit.

Old opener, no sensors

Openers 10–15+ years old, or without safety sensors, are due.

What we do: LiftMaster (our go-to) or Genie installed, $800–$1,400 with labor, old unit hauled away.

Chamberlain or Craftsman opener

Made by the same company as LiftMaster, and we repair them every week.

What we do: Logic boards, gears, sensors, wall controls, remotes and keypads; replacement quoted if a repair isn’t worth it.

What garage door opener repair and installation cost

Posted prices, the same everywhere we work. Your tech confirms the price in writing before a wrench turns. See all our prices.

Opener repair

$49.95 visit

  • Diagnosis, tune-up and 25-point safety inspection
  • Repair priced in writing before work starts
  • Visit waived with any repair
  • LiftMaster, Chamberlain, Craftsman, Genie and more
MOST COMMON

New opener installed

$800–$1,400

  • LiftMaster (our go-to) or Genie
  • Old unit removed, remotes programmed, safety tested
  • Workmanship + manufacturer’s warranty
  • $100 off right now

After-hours emergency

$250 flat dispatch

  • Outside 8:00 a.m. – 6:00 p.m. Mon–Sat, including early mornings before 8 a.m.
  • Repair quoted separately, in writing
  • Phones answered 24/7
  • Sunday calls booked for Monday

Oversized, heavy or custom doors are quoted in writing first. One coupon per household per job; coupons can’t be combined with each other or other discounts. Residential service only. Terms.

LiftMaster, Chamberlain, Genie and remotes

LiftMaster is our go-to and what we install most: the 2220L chain drive, the 6580L and 6690L belt drives and the 98032 wall-mount. See the LiftMaster openers we install. We also install Genie for homeowners who want to stay with Genie.

Chamberlain and Craftsman openers are made by the same company as LiftMaster, and we repair them like any other: logic boards, gears, sensors, wall controls, remotes and keypads. We also diagnose and repair Genie, Guardian, Kwikset, Marantec, Linear, Sommer and most other brands.

Remotes and keypads: LiftMaster’s M-series remotes and keypads work with LiftMaster, Chamberlain and most Craftsman openers made after 1997, and the U-series universal ones cover other brands. We program them, plus car built-in buttons, on the visit. Want to try it yourself first? Our remote programming guide has the steps.

Belt, chain or wall-mount: chain is the cheapest and the loudest; belt runs quiet, which matters when there’s a bedroom next to the garage; a wall-mount (jackshaft) sits beside the door, frees the ceiling and is the quietest of all.

Recent garage door opener jobs

Real opener jobs from our job records. Photos are our own; addresses and names stay private.

LiftMaster chain-drive opener mounted to a garage ceiling
Surprise · 85374Jul 2026 · Tech: Jack

Installed a new LiftMaster 2220L chain-drive opener and a 3-button remote.

LiftMaster belt-drive opener with its built-in light on
Phoenix · 85041Oct 2026 · Tech: Jack

Installed a LiftMaster 6690L belt-drive opener, replaced both springs and added a strut.

Torsion springs and center bearing after a spring replacement
North Phoenix · 85086Aug 2026 · Tech: Jack

Installed a LiftMaster 6690L belt-drive opener with 5-year springs, new rollers and hinges.

New torsion spring on the shaft after a spring replacement
Scottsdale · 85260Aug 2026 · Tech: Jack

Installed a LiftMaster 2220L chain-drive opener and replaced both springs.

What customers say

A broken 22-year-old opener, in the customer’s own words. 4.9★ across 600+ Google reviews.

★★★★★Tech: Jack
“They responded quickly to my broken 22-yo garage door opener, and we reviewed everything thoroughly before any work was started. There were NO surprises. Jack worked hard in the AZ heat, and my garage was clean when he left.”
Audrey T. · Google · Sep 2026

Garage door opener questions

How much does garage door opener installation cost in Phoenix?+

Most of our opener installations range from $800 to $1,400 with labor included.

The price depends on the model, horsepower, electronics and your door’s current configuration. Every install includes removal of your old unit, setup, alignment, remote programming and full safety testing, backed by our workmanship warranty and the manufacturer’s warranty. There’s $100 off a new opener installation right now.

How much does garage door opener repair cost?+

It depends on the part, and you get the price in writing before we start.

Our $49.95 visit (a tune-up and safety inspection) is waived when you approve any repair. If a new opener makes more sense, we’ll show you why and quote both.

Do you repair Chamberlain and LiftMaster openers?+

Yes. We repair LiftMaster, Chamberlain, Craftsman, Genie, Guardian, Kwikset and most other openers.

That includes chain, belt and wall-mount (jackshaft) models: logic boards, gears and sprockets, safety sensors, wall controls, remotes and keypads. New openers we install are LiftMaster, our go-to, and Genie.

Should I repair or replace my garage door opener?+

Repair a younger opener when a single part failed.

Replace it when it’s roughly 10 to 15+ years old and the logic board, gears or remotes keep failing, or if it has no safety sensors.

Why does my opener run but the door doesn’t move?+

Usually a stripped gear and sprocket, a worn trolley, or a trolley that was disconnected by the red release cord.

If a spring is broken, the opener can’t lift the door at all, so we check the springs before blaming the opener.

Why won’t my garage door close all the way?+

Most often the safety sensors are dirty, out of line or blinded by low sun.

Otherwise the close limit or force setting needs adjusting, or the sensor wiring is damaged.

Can you program my remotes, keypad and car?+

Yes. Our tech programs remotes, keypads and car built-in buttons (HomeLink) on the visit.

LiftMaster’s M-series remotes and keypads work with LiftMaster, Chamberlain and most Craftsman openers made after 1997, and the U-series universal ones cover other brands too.

Can you add Wi-Fi or app control to my opener?+

Often, yes.

Many newer LiftMaster openers have myQ built in, and many older openers can get app control with a smart add-on. We check compatibility on the visit.

Belt drive, chain drive or wall mount: which should I choose?+

Chain for durability and value, belt if there’s a bedroom next to the garage, wall-mount for high ceilings or storage racks.

Chain is the cheapest and the loudest. Belt costs more and runs quiet. A wall mount (jackshaft) sits beside the door instead of on the ceiling and is the quietest option.

How long should a garage door opener last in Phoenix?+

Manufacturers usually quote 10 to 15 years; in an attached Phoenix garage, expect the shorter end.

Garages that regularly pass 120 degrees in summer are hard on logic boards and capacitors, and monsoon dust is hard on rails and photo eyes.

Is it safe to keep using an opener that grinds or strains?+

Not for long.

Grinding usually means worn gears, and straining often means tired springs making the opener lift the door. Stop using it and have the door and opener checked before it fails completely.

Do you offer emergency opener repair?+

Phones are answered 24/7, and techs run Monday to Saturday, 8 a.m. to 6 p.m.

After hours (outside 8:00 a.m. – 6:00 p.m. Mon–Sat, including early mornings before 8 a.m), emergency dispatch is a flat $250 plus the repair. Sunday calls are booked for Monday.

How long does it take to install a new garage door opener?+

Most opener installations take a couple of hours.

That includes setup and testing for safety and performance before we leave.

How do I tell how old my Genie opener is?+

Look at the program button on the motor unit.

A round “Learn Code” button means an Intellicode Genie from about 1995 to 2011. A square program button with + and – buttons means 2011 or newer. Very old Genies use tiny switches inside the remote instead of a learn button.

Opener quit? Same-day service from our Deer Valley shop.

When the schedule allows. A person answers 24/7.

Get your upfront price

Max. file size: 1 GB.
Consent

Call (623) 219-8460 Get Fast Quote
Call Now!